-
מגבר דיגיטאלי מונובלוק 600X1
-
סט רמקולים קואקסיאלי 2WAY עוצמה 80 וואט "6.9 מפרטי טכני: Woofers: injection-molded, mica-filled, polypropylene cone body, 1.25-inc (32mm) voice coil, flat-profile/ symmetrical-roll spider, butyl rubber surround. Tweeters: I-inch (25 mm) treated textile soft dome tweeter, neodymium magnet, ferrofluid cooled and damped. Continuous Power Handling: 80 Watts (RMS Method) Frequency Response: 45 HZ – 22 KHz (± 3 dB) Efficiency @ IW / I m: 91.0 dB Nominal Impedance: 4 ohms Included Components and Parts: - Two VR690-CXI 6 x 9 inch Coaxial Loudspeakers - Two Metal Grilles and Grille Trays - Two Bottom-Mount Spacer Asse,blise - Butyl adhesive putty for grilles - Eight #8 x 2-inch (51 mm) Mounting Bolts and Locking Nuts - Sixteen #8 Flat Washers - Eight Mounting Clips - Two 5.2 mm Female Crimpable Connectors - Two 2.8 mm Female Crimpable Connectors
-
JL Audio HD600/4
These Class D amplifiers use less power, take up less space, and generate less heat than traditional amp designs — you can even stack them up to create a sweet-looking installation.
HD Series amplifiers reproduce your music with exceptional accuracy, so you'll hear high-fidelity sound even under the most demanding conditions. JL Audio uses Single Cycle Control™ technology to eliminate the excessive signal distortion that's plagued Class D amplifiers in the past. Differential-balanced inputs eliminate noise before it hits the preamp stage, and allow you to connect the amp to just about any in-dash stereo. You'll hear clear, true, studio-quality audio, exactly what you expect from JL Audio.
General Features:
- 4-channel subwoofer amplifer
- 150 watts RMS x 4 (1.5 - 4 ohms per channel)
- 300 watts RMS x 2 bridged (3 - 8 ohms per channel)
- variable high- and low-pass filter (50-500 Hz 12 or 24dB/octave)
- subsonic filter and output polarity control
- removable power and speaker plugs
- optional wired remote for level control
- Class D amplifier design
- MOSFET power and output stages
- differential-balanced inputs eliminate noise from your vehicle's electrical system
- speaker- and preamp-level inputs
- preamp outputs
- 4-gauge power and ground leads and a 80-amp fuse recommended — wiring and hardware not included with amplifier
- 10-3/4"W x 2"H x 7-7/8"D
- no onboard fuses — when installing multiple amps in a system, an additional 80-amp in-line fuse between the distribution block and the amplifier is recommended
-
CLS113RG-W7AE
Enclosed Subwoofer System with Single 13W7AE-D1.5 Subwoofer Driver, Black Carpet (1500 W, Dual 1.5 Ω) - Sealed Enclosure
For those who seek the ultimate in compact-enclosure sub-bass fidelity, we offer this sealed ProWedge™ system, in which the superb performance capabilities of the W7AE subwoofer driver are harnessed within a compact, sealed enclosure. This system has it all: extension, impact, detail and smooth response... at any listening level.
This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 13W7AE-D1.5 and has been fine-tuned through extensive real-world listening.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal.
The angled-back design saves precious cargo space by allowing the enclosure to fit tightly against the back of a vehicle's rear seat.
Finish: Black, high-grade automotive carpet, with gloss-black laminated decorative front baffle trim. Three solid aluminum bars provide stylish and rugged woofer protection.
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 500 - 1500W
Nominal Impedance: Dual 1.5 Ω